Close
Filters
Search

Specialty

View as Grid List
Sort by
Display per page

STFS - IMM Ultra High Jacking

Combine arimid and steel braid construction for compact design. Lieghtweight and flexible. Small bend raduid for use on hose reels. Anti-abrasion cover. Standards: Meets material handling institute specification IJ 100 (1/4") for hydraulic hose and assemblies used with jacking systems. Tube: Polyester elastomer Reinforcement: One or two braids of aramid fibre plus one steel braid Cover: Polyurethane, black, pinpricked, white ink-jet branding Recommended Fluids: Hydraulic fluid, petroleum-based;Glycol, water-based Temperature Range: -40°F to +212°F (-40°C to +100°C) continuous, +158°F (+70°C) for water-based fluids
$0.00 inc GST

J2AT - Gates Wire Braid Jacking

Recommended For: Hydraulic jack applications. Meets Material Handling Institute specification IJ 100 for hydraulic hose and assemblies used with jacking systems. Meets flame resistance acceptance designation MSHA 2G Tube: Black oil resistant, synthetic rubber (Nitrile-Type C). Reinforcement: Two braids, of high-tensile steel wire. Cover: Black, oil and abrasion resistant thin synthetic rubber (Modified Nitrile - Type C ). Temperature Range: -40° F to +120° F (-40° C to +49°C). Couplings: Super-Crimp and Ezi-Crimp series.
$0.00 inc GST

PC - Power Clean

Recommended For: For use with hot or cold water, high pressure cleaning equipment. NOTE: Not recommended for steam service. Tube: Synthetic rubber specifically compounded to handle high pressure water service. Reinforcement: High tensile steel 1 & 2 wire braid. Cover: Specifically compounded to handle high pressure washer environment. Temperature Range: -40°F to +250°F (-40°C to +121°C) . Increased operating temperature will reduce hose assembly service life. Couplings: Super-Crimp and Gates Mega-Crimp series.
$0.00 inc GST

RFS Red Fire Suppressant Hose

Recommended for: Low pressure powder fire suppressant applications in mining, forestry and fire fighting equipment. The red cover is for easy visual identification in these applications. Standards: Meets performance requirements of SAE 100R1 Tube: Black, oil resistant, synthetic rubber (Nitrile) Reinforcement: One braid of high-tensile steel wire Cover: Red, oil- and abrasion-resistant synthetic rubber (Modified Nitrile) Temperature Range: -40°F to +212°F (-40°C to +100°C)
$0.00 inc GST

AFX - Teflon PTFE

Smooth Bore Heavy Wall Imperial range Meets or exceeds SAE 100R14 working pressure. (dimensionally not the same as SAE 100R14) Recommended For: Hydraulic oil lines, Tubo chargers, Steam, Canning sealant lines, Plastic/Rubber moulding presses, Compressor discharge, Fuel lines, Paint spray, for other applications contact Southcott Pty Ltd. Tube: Teflon* (PTFE) hose core is manufactured from premier quality resin, smooth bore heavy wall. No pigments or additives are incorporated thus giving the hose liner a translucent appearance free from any contamination. Cover/Reinforcement: Stainless steel wire braid produced from AISI 304/S15 or BS970-1 1996 quality hard drawn tensile stainless steel wire. Temperature Range: -60°C to +260°C Couplings: Child: Super-Crimp. Warning: PTFE has a very high electrical isolation value, a damaging electrostatic charge can build up inside the hose when electrically resistive fluids/gases are being transmitted at high velocity. Review the potential for electrostatic discharge for every application. If in doubt contact your Southcott agent. SAE 100R14 working pressures are rated for dynamic applications. Maximum working pressures will vary depending on operating temperature and impulse frequency.
$0.00 inc GST
Close